Storing Cookies (See : http://ec.europa.eu/ipg/basics/legal/cookies/index_en.htm ) help us to bring you our services at overunity.com . If you use this website and our services you declare yourself okay with using cookies .More Infos here:
https://overunity.com/5553/privacy-policy/
If you do not agree with storing cookies, please LEAVE this website now. From the 25th of May 2018, every existing user has to accept the GDPR agreement at first login. If a user is unwilling to accept the GDPR, he should email us and request to erase his account. Many thanks for your understanding

User Menu

Custom Search

Author Topic: Kapanadze Cousin - DALLY FREE ENERGY  (Read 11717706 times)

skywalker66

  • Full Member
  • ***
  • Posts: 182
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6300 on: October 31, 2014, 11:06:44 AM »
@ URFA

Hi !
What is hissing in your setup when you move your hand near the cooper antenna ?  Is main yoke, is 24V power source, or something else?
You get interesting effect in deed, seems you are close, but from what I see you may have mess some connections at output side than Ruslan's hand schematic from video, from where probably your large consumption of current. God luck !

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6301 on: October 31, 2014, 11:15:28 AM »
Guys, some question here. On the picture below is my basic structure of the device.  I have it a bit different than Ruslan.or my Tesla coil  I used 0.3 wire separated with the sawing threat and varnished. If the principle is based on the Ionization of the air I think the surface matter. My Tesla is long 30 cm ( Ruslan has around10 cm) and it is a half wave of 1.87 MHz- which is my bifilar"grenade" coil. My question is - does it matter in what direction is wound primary of the Tesla??  I believe not, just want to make sure. May be somebody has experience already with that.  My next question is that opposite  wound coil right behind the Tesla coil. If I have my all Tesla already wound in that direction do I have to put that extra wire there and in what direction if my Tesla is wound in opposite to Ruslans? 

Thanks,

Hi John.K1,

nice build, but looking at your Kacher, it seems to me it must be working in "dual quarter wave" mode  :)
So you probably have 1 quarter wave going to the right side from the center primary coil, and another quarter wave to the left.
No idea what this has for influence on the whole, but it could be it cancels out something you need.

I would suggest to move the primary to the left (bottom) of the Kacher secondary, and probably it will start working in
single quarter wave mode, meaning half of your frequency (935KHz) so you might need to remove some secondary wiring to get back to 1.87MHz

I understand that the Kacher secondary needs to be wound the same direction as the Grenade coil layers 1 and 2.

For what its worth,   regards Itsu

corry

  • Newbie
  • *
  • Posts: 27
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6302 on: October 31, 2014, 11:32:18 AM »
...
Ruslan Says:
.... Because no samozapita....


But, what does this mean?

MenofFather

  • Hero Member
  • *****
  • Posts: 943
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6303 on: October 31, 2014, 11:48:12 AM »
But, what does this mean?
Because no selfrunning. Samozapit is selfrunning.

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6304 on: October 31, 2014, 12:44:07 PM »
Hi Void.
In fact you know everything about my setup. I used Ruslan's schematic. He drew in his video. His scheme was published by Enjoykin and GeoFusion.It was posted a few pages ago in this forum.
In my setup.
Power consumption of kacher: 24 V  1.8-2 A
Power consumption of push pull driver circuits: Without kacher 24V 2A but I measured when kacher runing Its power consumption is growing about 24V 7-8 A.
Power consumption of kacher and push pull driver totally 9-10A(24V)
I have 4x40w and 1x100w  220v light bulbs. Totaly 260w and When kacher run they are fully brightness.
My setup not OU.I only share this video with you to show the effect of Kacher. I'm still working on this system like you.

Note: I can not fully express myself Because of my bad english :'(

All the best..

Hi Urfa. Thanks for the details on your setup. Your English is fine.
Keep at the experiments. You are doing well. :)
All the best...
« Last Edit: October 31, 2014, 02:51:18 PM by Void »

John.K1

  • Hero Member
  • *****
  • Posts: 679
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6305 on: October 31, 2014, 01:28:54 PM »
Hi Itsu, lads

Thank you for your comment. May I ask you how did you select your inductor on your Katcher?  As you can see on the picture  I have tested most of what I have found at home :)  Most of them was overheating. The one as on my  picture seems to stay cool. But I cant get nice sinus shape yet. What would you recommend here. Is it matter of capacitors? The Tesla has its power as you can see 5-6 mm ion stream from the end of the wire and it reads frequency 1.14 which is not a issue at the moment. 

Thank for advice.

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6306 on: October 31, 2014, 02:14:06 PM »
Hi John.K1

i guess you mean with "inductor" the common mode choke i see laying around on your bench.

I just grabbed one i had laying around, but as there are some amps running, you need to look for thick wired ones, and
according to Hoppy, it needs to be in the uH range,  not mH.

My present one does not work (the Kacher i mean) when the minus lead is not bypassed on my common mode choke (its 2x 3mH), so i need
to find/build myselve a thick wired / uH ranged one too.

It looks like you are probing the base and collector of your Kacher, right? (scope screenshot)
For checking the output of the Kacher, just lay a probe near the Kacher secondary or antenna and look there for the sine wave,
it probably will be fine.

Regards Itsu

Сергей В.

  • Full Member
  • ***
  • Posts: 224
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6307 on: October 31, 2014, 02:50:11 PM »
Hi Itsu

Hoppy

  • Hero Member
  • *****
  • Posts: 4135
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6308 on: October 31, 2014, 04:39:56 PM »
Hi John.K1

i guess you mean with "inductor" the common mode choke i see laying around on your bench.

I just grabbed one i had laying around, but as there are some amps running, you need to look for thick wired ones, and
according to Hoppy, it needs to be in the uH range,  not mH.

My present one does not work (the Kacher i mean) when the minus lead is not bypassed on my common mode choke (its 2x 3mH), so i need
to find/build myselve a thick wired / uH ranged one too.

It looks like you are probing the base and collector of your Kacher, right? (scope screenshot)
For checking the output of the Kacher, just lay a probe near the Kacher secondary or antenna and look there for the sine wave,
it probably will be fine.

Regards Itsu

Even my 300uH choke is too high, so 100uH or less may be OK by re-winding with thick wire.

Regards
Hoppy

Void

  • Hero Member
  • *****
  • Posts: 2333
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6309 on: October 31, 2014, 09:45:34 PM »
Even my 300uH choke is too high, so 100uH or less may be OK by re-winding with thick wire.
Regards
Hoppy

Hi Hoppy. What happens when the choke inductance is too high?
All the best...

d3x0r

  • Hero Member
  • *****
  • Posts: 1433
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6310 on: October 31, 2014, 10:35:40 PM »
Hi Hoppy. What happens when the choke inductance is too high?
All the best...
if you have a small capacitance in front of it; it will limit the current, and upset the resonant frequency... adding a larger cap in front of the coil should cover larger chokes ... allowing it to be in a DC mode rather than back oscillating to its supply...

itsu

  • Hero Member
  • *****
  • Posts: 1845
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6311 on: October 31, 2014, 11:13:43 PM »

I made a new Grenade coil according to the now known specifications:
 
2.5mm² stranded copper wire OD = 3mm, total length is 38.5m with 2x 0.5m connection leads (coil length 37.5m).
Layer 1 and 2 are  19cm long and are resp. 56 and 55 turns CCW
Layer 3 and 4 are 9.5cm long and are resp. 26 and 25 turns CW
Layer 5 and 6 are 4.5cm long and are both 12 turns CW

Tube OD is 5cm

Inductance measured is 168uH @ 1KHz and 166uH @ 100KHz

Main (and almost only) resonance frequency peak is at 1.290 MHz, see screenshot of the frequency scan (1KHz -> 10MHz)

Video here:  https://www.youtube.com/watch?v=2G_nFy4zIek&feature=youtu.be


The Kacher secondary will be wound opposite to the Grenade coil layers 1 and 2 meaning CW
The inductor around the Grenade will be the same wire with a length of 18.75m (half the Greneade length) and wound CW like
the layers 3/4 and 5/6 of the Greneade, but in TESLA BIFILAR way, and probably in 3 layers (2 won't fit on the 9.5cm available).
Tesla bifilar means 1st layer right to left, then straight back to the right and starting there again layer 2 and probably layer 3.

Regards Itsu

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6312 on: November 01, 2014, 12:04:59 AM »

hi URFA,

I was impressed by your video but at quick glance i have also spotted 2 mistakes.

Please avoid using full-bridge rectifier module at cost although it looks like most easy solution.I have already discussed about this previously that this module is only designed for mains frequency 50/60hz.

The catch is if you try to try at higher frequency in khz range this module won't able to deliver the same Amps as it was rated for.Do check all full bridge recitifer datasheet and it is very rare to spot a module
which can support higher frequency.

Please assemble using diodes like UF5408 3Amp x 2 in parallel for each side to form full-bridge rectifier as an example.

Another previous discussion the full bridge diodes or module inside the 24volts power supply may need to be altered to cater for the high frequency.

Thanks for the video.Keep it up.

Hi magpwr.
You are right, but I've used it for any other purpose,not for rectified voltage end this bridge rectified was unnecessary. Not to have any effect in this my setup.I remove it from the device.
Thanks.

URFA

  • Jr. Member
  • **
  • Posts: 70
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6313 on: November 01, 2014, 12:18:09 AM »
@ URFA

Hi !
What is hissing in your setup when you move your hand near the cooper antenna ?  Is main yoke, is 24V power source, or something else?
You get interesting effect in deed, seems you are close, but from what I see you may have mess some connections at output side than Ruslan's hand schematic from video, from where probably your large consumption of current. God luck !

Hi skywalker66.

Hissing sound coming from the Common mode inductor.( mini tv yoke in the video). But some times when I change the push pull generator frequency then hissing sound comin from main yoke(20-30%) and mini yoke(Common mode inductor)(70-80).

Regards

NickZ

  • Hero Member
  • *****
  • Posts: 5225
Re: Kapanadze Cousin - DALLY FREE ENERGY
« Reply #6314 on: November 01, 2014, 02:52:54 AM »
  Itsu and All:
  Nice grenade!  But, now I'm confused...  I had thought that the bifilar coil was wound on the left side of the main grenade coil. And the end of the 48,48, 24,24, 12,12 turns coil was supposed to end up on the right side of the grenade. So, the  bifilar coil should be next to the Kacher coil side, and not on the right side.
  Is this wrong??? Or which way is it, as done by Akula/Ruslan.