Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

Custom Search

[Omnibus]

@ken_nyus,

You may have a point. I've noticed difference in behavior and probably easier appearance of the effect when more than one stators are forced AGW.

Just to be clear, with equal spacing of rotors?

like at the 1/2 or 1/4 points.

Don't quite understand what you're asking. All stators are at 5mm distance form the rotor. Is that an answet to what you asked?

[hoptoad]

Please allow me to have some doubt in what Bill writes in his posts.

@Shirakawa
You don't need anybody's permission to doubt anything that anybody says or claims.
Cheers all. Hope you find what you think you are looking for.

[rice]

hey Omnibus, did not you say that you have built a working model and it accelerates.  lets see a vid or pic.  i am indeed interested to see it

[Omnibus]

hey Omnibus, did not you say that you have built a working model and it accelerates.  lets see a vid or pic.  i am indeed interested to see it

Go back and read what I've said on the subject.

[MeggerMan]

Hi Bill,
Yes I remember you from the Joe Cell days too and I have no problem with you reporting on your results - in fact I still have 3 joe cells in the garage, I noticed some very odd effects with the tests that I carried out.

Anyway, when you had the 1 minute sustained run, were you able to monitor the RPMs ?

From the video you posted earlier it is very apparent that a hand spin of the rotor soon slows to a stop in 15-20 seconds so a sustained run of 1 minute is a big step forward.

@DA,
I have made your suggestion about angled stators to Al, I too had this idea a few pages back.

@Bruce,
Regarding the N35 magnets, I got Al to measure the vertical repulsion distance between two rotor magnets, 1/4" dia x 1/2" rod and he measured it to be 30.5mm which is about what I got with the ones I ordered from S&J magnetics at 31.5mm, if someone has some N38 or N35 rods they could perhaps do the same test and feed back the results.

Regards
Rob

[RunningBare]

@alsetalokin is still evading the answer to this simple 'yes' or 'no' question. He thinks he doesn't owe the answer to anyone but he actually does if he wants to preserve his integrity.

"chuckles"

alsetalokin is in a good job, he gets paid well....and more importantly he is an anonymous internet user, I'm sure his integrity where it really matters is fully intact.

[Omnibus]

@alsetalokin is still evading the answer to this simple 'yes' or 'no' question. He thinks he doesn't owe the answer to anyone but he actually does if he wants to preserve his integrity.

"chuckles"

alsetalokin is in a good job, he gets paid well....and more importantly he is an anonymous internet user, I'm sure his integrity where it really matters is fully intact.

Don't be so sure. If he were my employee or a grad student and I knew his current behavior that won't be so and I'm not alone in that.

[ken_nyus]

@ken_nyus,

You may have a point. I've noticed difference in behavior and probably easier appearance of the effect when more than one stators are forced AGW.

You noticed a difference when you tried stators equally spaced, like at 90 degree intervals or 180 degree?

(rather than the original 27.7 degree intervals)

Or just when you tried more than one?

[leeroyjenkinsii]

Overunity is like the search for bigfoot.

[vipond50]

To vipond50
Can you tell me what stator bearing you started out with and what you are using now when you get the three stators to sync.
Also it might be just the camera, but the rotor mag look somewhat different, are they the 1/4 by1/2 round that are in most of the spec i have seen
thanks and keep up the good work
HT

Hi Hydro
Sure Glad to help
1. The Stator bearing is a R3-HA! manufactured by Bearings. This right off the box
2. The two bearings have a small thin washer" will mic " between them and another washer to give clearance off the base plate Will also get a Pic of the assembly layed out.
3. The Rotor mags are 1/4" diameter and 1/4" long N42's. I stacked them up (four) to give the length u see.

Hope this helps
Regards
Bill

I machined a longer adapter to house the bearing