Free Energy Alternative ZeroPoint Green Tesla Power Open Source Research Forum OverUnity.com

@ Gadgetmall

No Rush on this request, whenever you get a chance 

I'm trying to put together a Materials and build list to try to replicate your setup.  What I'm looking for are questions regarding the following components:

Welding Rods - Type ?
Length of Welding Rods ?
PVC pipe for primary coil- ID/OD (I think you mentioned 1/4" ID in your video) ?
Length of PVC pipe ?
Primary Coil Wires - 2 wires as per circuit, CW or CCW?
Primary Coil End caps - What type of plastic and size?
High Voltage Diode going to Primary from capacitor - Type & Values?
Primary Coil Winding - There's a discrepancy on your video regarding the gauge size of the wires used, is the size in the above schematic the latest and correct for the wire size?
Secondary Coil Winding (Piggy back coil) - ID/OD X Height?


That's it for now, I'll probably ask you more questions later 

Regards,
Paul

@GOAT
Paul, here is the latest Cleaned up Schemitic and i will try to find the time to fill in the blanks .I am a Single daddy with a 7 year old girl and we have a Birthday party this weekend and lots of preperations to make .   Re: Fusionchip's Bedini Feedback to Source!!!
« Reply #2 on: January 12, 2009, 12:00:08 AM » Quote 

--------------------------------------------------------------------------------
@ Gadgetmall

Again, no Rush on this next set of questions, I know it's a lot to ask but whenever you get a chance. 

Amendment 1:

1.  Welding Rods - Type ? i will try and find out by a welder . they were junk yard picks-rusty
2.  Length of Welding Rods ?will measure
3.  PVC pipe for primary coil- ID/OD (I think you mentioned 1/4" ID in your video) ? 1/4 sch 20
4.  Length of PVC pipe ? will measure later
5.  Primary Coil Wires - 2 wires as per circuit, CW or CCW? CCW
6.  Primary Coil End caps - What type of plastic and size?TEFLON cut in  2 inch DIA circles
7.  High Voltage Diode going to Primary from capacitor - Type & Values?RCA SK3606
8.  Primary Coil Winding - There's a discrepancy on your video regarding the gauge size of the wires used, is the size in the above schematic the latest and correct wire size? correct in new schemitic .Verified 16 and 20
9.  Secondary Coil Winding (Piggy back coil) - ID/OD X Height?will measure later
10.  Weight of Primary coil?..minus the core  5 1/2 pounds
11.  Weight of Secondary coil (Piggy back coil)?a tiny bit over 1 pound .i have a postal scale no grams
12.  Base of Primary coil, materials used? Bakalite i think . it was the mercury relay base .looks like it has some fiber in it ? kind of heavy but looks like plastic too ?? I dont know but its from the 60's 
13.  Size and Strength of Neo magnets used on HDD motor and Platter plates?  ebay Cylinder 1x1/4 n48
14.  Neo magnets facing N or S at the coil core? N
15. i would like to add that the piggyback coil might be wound cw or ccw . there is some black stuff sealing it and the outside layer is like black cloth or fabric . i peaked at it and got the wire size but no real indication of how it is wound so ? Varable. I think the aire core hole has somthing to do with the properties . also i dont know if its copper or aluminum or what because it terminates in a sheathing with connectors crimped on it . Couild be iron copper aluminium gold silver . i dont know but i know its worth a lot to me .No its not for sale unless you got a million dollars
Best regards guys . i will return
Al AKA fusionchip AKA 4Chirstonly1 AKA GADGETMALL 

H@all . ok im still trying to improve this circuit to obtain real use of my machine with inverters . I have experimented with a reed switch in series with the primary power coil which slowed down the rotor and produced more power . It was an experiment and i will probably hard wire it in later . Also i have been testing a second Trigger coil as pictured and i think i like this the best . it spins much faster and i will be running this setup to determine if it sucking power to fast and i lose the ove unity i have with one trigger . i will run this setup for a bout a week and let yall know if this is an improvement or not .. the extra trigger is in series with the primary trigger . also in the second photo i have added a second transistor in parallel with the first one hoping to improve the draw of voltage on my primary to attempt another try at running off the caps alone . The first attempt left me with a pile of bad 2n3055's as the voltage coming off the piggy back coil is too high for the 2n3055 and Blows them instantly . Maybe two in parallel will increase the capacity to 200 volts and not kill the circuit . i will let you know after a week of running the 2nd trigger . One note comes to mind . I don't think the setup is critical other than the fact that the coil configuration of any bedini could be changed with the core protruding out the back of the coil . the reason i am telling you this is if you have a bedini already make a new coil like mine and use an experimental piggyback on it and see if you get the results i do . the more windings on the primary the less current it will draw . Mine can run on as low as 6 ma's . and as high as 500 ma's . I built a bedini for my brother not like my design except we left the core open and i put my piggyback coil on his machine . It (primary)remained the same running voltage for 6 hours thus proving that the design is not to critical . i think with a little rewinding of the coil i made for him it would self run too . the only think is he tried to wind a coil like mine but wound it on a longer pvc sticking out the back and it did not produce the voltage or current My Magic coil does . BUT he did not use tiny wire . i think it might have been 26 and i think he wound it counterclockwise the same as the primary . he gave up cause it took days to unwind the wire from a BIG toroid for his piggyback and left it like that . I guess when we get the time to undo it and rewind it the other way with the same wire we would get better results .. Ok go for it !!!!!

@ gadgetmall

Thanks for posting the picture of the piggyback coil. 

I have a brother in law that works in industrial electric circuits, I will forward him all the information you gather and I'll try to find out if he's ever come across an old Mercury solenoid with a coil like this in his line of work.  He possibly might know of other units that use a similar coil.

Edit:  Was the solenoid switch that you had look something like this (see picture below) and did it have any markings on it that you would still have access to?

http://www.mercuryrelays.com/shoppingcart/agora.cgi?&product=35amp

Again sorry for all the questions and please do not pressure yourself to find the answers.

Thanks again,
Paul

The Gold Disks i use are from one of the first hards drives made by Segate and i understand  the platters are made with platinum, gold and palladium along with Aluminum . But this don't matter !! Because it self charges in oscillation mode even stronger sooo i would not worry about the material of the rotor . its the coils !!! and the way they run with minimum current draw . that is another key . get your bedini running at 10ma or less either turning the rotor or solid state ! That is all i can do for now . i'll come back later in the week with some test results and coil measurements . Kirk out !